HVAC SERVICES IN EATON NORTHERN COLORADO

By the team at Homegrown Heating and Air Conditioning.

Every Service We Cover in Eaton

We work on the whole system, not one appliance:

• Furnace repair, and furnace installation and replacement
• AC repair and AC installation
• Heat pump installation and repair, including dual-fuel systems
• Heating maintenance and tune-ups
• Indoor air quality and filtration upgrades
• Whole-home humidifiers
• Ductwork repair and sealing
• Smart thermostat installation
• Emergency HVAC repair, same day, seven days a week

Most Eaton projects come down to one of three decisions, covered in detail on our furnace installation, AC installation and heat pump installation and repair pages.

What Electric-Ready Means for HVAC Services in Eaton

Eaton’s newest homes are built to be ready for electric heat. Under Ordinance 664, effective January 1, 2026, the Town enforces the 2024 International Codes together with the Colorado Model Electric Ready and Solar Ready Code, as listed on the Town of Eaton building and permitting page.

For a new home built with a gas furnace or gas water heater, the electric-ready code requires the builder to plan for a future electric replacement:

• A dedicated circuit and reserved breaker space in the electrical panel
• A receptacle or junction box near the gas appliance
• Physical space for future heat pump components

That last point matters more than it sounds. A ducted heat pump needs an outdoor unit, a coil or air handler, and often an electric backup heat strip, none of which a gas furnace uses. In an older home, adding that capacity can mean a panel upgrade, a longer wiring run and a tight fit in the utility room.

In an electric-ready Eaton home, much of that work is done before you ever call us. We still verify the reserved circuit and panel space against the nameplate of the equipment we propose, because a reserved circuit sized for one product may not match another.

Utilities and Rebates in Eaton

Eaton homes buy natural gas from Atmos Energy. Electric service comes from Xcel Energy for most of town, while some addresses are on Poudre Valley REA. The Town’s own permit form asks which one serves the property.

• Atmos Energy: 80 percent of cost, up to $3,000, on a 95 percent AFUE or higher furnace, $50 toward an annual tune-up and $663 for qualifying duct sealing.
• Poudre Valley REA: $500 or $1,500 for an air-source heat pump depending on size, capped at 50 percent of equipment cost, plus a $500 dual-fuel bonus.
• Xcel Energy: as your electric utility, Xcel pays its standard heat pump rebate, effective October 1, 2026: $300 per cooling ton for a qualifying ducted air-source heat pump, or $750 per heating ton for a cold-climate model. Xcel reserves its bonus amounts for homes heated with Xcel natural gas, so an Atmos-gas home gets the standard rate.
• Colorado Heat Pump Tax Credit: applied as an invoice discount on a qualifying 2026 install.

Permits and Contractor Licensing in Eaton

The Town Clerk’s office issues permits through CommunityCore, and SAFEbuilt performs inspections. Eaton’s over-the-counter permit form includes checkboxes for new or replacement furnaces and air conditioners, and the residential permit form notes that Manual J, S and D load and duct calculations may be required.

Eaton requires a Town contractor license for all trades, including mechanical, and the permit form asks for the mechanical contractor’s Town license number. Ask any contractor for theirs before signing. We hold Town of Eaton license 25EAT-MCL-1069 and confirm the permit path for your address before scheduling permitted work. We also pull HVAC permits in unincorporated Weld County, where no contractor license is required.

Sizing Equipment for an Eaton Winter

Weld County uses a winter design temperature of 1 degree for the area. A furnace or heat pump has to hold the house at that point, which is why we size from a load calculation rather than the old unit’s label.

At about 4,840 feet, gas appliances also need altitude adjustment per the manufacturer’s instructions. If your home was one of the roughly 2,500 that lost gas service during the June 2022 Atmos outage, it is worth having burners and pilots checked at the next tune-up, since every appliance had to be relit.

What an Eaton Service Visit Includes

• A measured diagnostic with written readings
• An upfront price before any work starts
• Electrical capacity checks before any heat pump quote
• A combustion and safety check after gas appliance work
• A plain answer on repair versus replacement

Two Jobs That Show the Approach

Cold-weather calls are where speed matters most. One homeowner’s furnace could not keep up during a hard freeze.

Tyson Miller wrote: “They came and fixed my furnace that was not coming up to temperature (it was negative 6 degrees out) with very little notice.”

A furnace that runs but cannot reach temperature is often an airflow, gas pressure or ignition problem, and we measure each one rather than guess.

The second job was a replacement. JWM wrote: “They were able to replace my furnace and add a/c on the day I requested. The work was high quality.” Adding air conditioning to an existing furnace is a common Eaton upgrade, and the load calculation decides the size. Read more customer reviews.

Request HVAC Service in Eaton

Tell us what the system is doing and whether the home is new construction. Contact Homegrown Heating and Air Conditioning to schedule HVAC services in Eaton.